Jack Davies | DIY Prototype Printed Circuit Board (PCB) Manufacture
14956
post-template-default,single,single-post,postid-14956,single-format-standard,ajax_fade,page_not_loaded,,qode-theme-ver-6.5,wpb-js-composer js-comp-ver-4.4.3,vc_responsive

DIY Prototype Printed Circuit Board (PCB) Manufacture

29 Aug DIY Prototype Printed Circuit Board (PCB) Manufacture

I have built a number of projects that required PCBs to work as well as they do, I produced a number of boards for my Ultimaker 3D Printer project and I thought I would document the process of making the Arduino shield for my MIDI Controller! For the prototype stage I manufactured the boards myself as it would have been too costly to send the board designs to be professionally manufactured on a one off basis. I produced the boards myself using these basic techniques and was able to save a substantial cost whilst ending up with a good end result.

 

Screen-Shot-2014-05-21-at-09.06.31

Circuit Board CAD Design

The first stage of manufacture was to design the board layout using a CAD package. I chose to use Eagle CAD which has a free version that was appropriate for my needs and is very popular within the maker community, I also have used it in the past so was pretty fluent in its operation and feature set. I created schematics of the basic circuit which I then routed into a board file.

 

 

 

 

 

Screen-Shot-2014-05-21-at-09.09.55Board Layout

The next stage of the design process was to convert the circuit diagrams to a board layout that could be transferred to copper clad fibreglass circuit board. The software allowed me to see which pins needed to be connected to each part, this made it easier to ensure the correct electrical connections were being made. I always try to make board single sided to enable a simplified manufacture workflow, however because the switches were on the top of the board and the Arduino was on the bottom I needed to solder on both sides. I could have used SMD tact switches but I already had a load of through hole ones I wanted to use.

 

 

Stencil Printing

IMG_3692After the computer design stage the Pads, Vias and Top layers were exported from Eagle for single sided boards and an extra Bottom layer for the double sided boards. The artwork was then mirrored and printed on to clear acetate sheet; I printed two copy’s so 2 sheets could be layered on top to eliminate and light leaks that could happen because of uneven toner coverage.

I got the acetate sheet from WHSmiths in the UK, you can buy it online too.

 

 

 

 

 

UV Exposure

I then cut the photo sensitive copper clad board to a size just larger than the acetate artwork which was then affixed to the photoresist side of the board with tape after removing the black protective film the circuit board. It was important to do this in a darkened room to prevent unwanted exposure. The board was then placed in the UV exposure unit for about 15 minutes to sensitise the area where there were no traces or pads.

IMG_3701 IMG_3700

 

Developing

After being exposed, the boards needed to be developed, this is done using a strong alkaline solution such as 1% diluted sodium hydroxide. However I had better success using a Seno developer which I bought in an applicator bottle similar to a shoe polish container with a sponge pad on the end. This made it much easier to develop areas of the board in a more localised way as I found using the sodium hydroxide solution created uneven results.

IMG_3713 IMG_3707

 Etching

After successfully developing the boards the traces and pads turned a green colour which could then be used as an etch resist. Green parts would stay copper and anything not green would be etched away, leaving just the fibreglass board remaining. The etching process is fairly easy but involves some hazardous chemicals and needs to be handled carefully. I used Clear PCB Etchant from Mega Electronics which is a relatively safe etchant but takes a little longer than Ferric Chloride which is the traditional choice and is stronger. However the clear is much less toxic and does not stain clothing. It comes in a powder which requires mixing with hot water to make a solution for etching PC boards. Once a solution is made up, the board can be submerged and the etchant will start removing the copper in the un-masked parts of the board. A small PCB usually takes about 30 minutes for the etchant to fully remove the unwanted copper, I found rubbing the board using an old toothbrush helped to speed the process up.

IMG_3719 IMG_3710

 

Special Treatments

The last stage was to finish the board by removing the etch resist with isopropanol alcohol or nail polish remover, this then exposes the shiny copper which can be soldered to straight away or finished with a solder mask. I bought a tube of green UV curable solder mask online relatively cheaply. This requires a similar process to the photo etch method to apply the mask to the board.  Another product that could be used was Liquid Tin which coats the copper traces and pads with a very thin layer of tin which helps with the soldering process and stops the coper oxidising.

 

IMG_3726 IMG_3728 IMG_3725

8 Comments
  • Denny Rowsell
    Posted at 01:53h, 15 October Reply

    I have read a few of the articles on your website now, and I really like your style of blogging. I added it to my favorites blog site list and will be checking back soon. Please check out my site as well and let me know what you think.

  • Sandra
    Posted at 03:58h, 31 October Reply

    Hi my name is Sandra and I just wanted to drop you a quick note here, I came to your DIY PCB Manufacture page and found it very informative. Thank You!

  • Neellereill
    Posted at 03:48h, 05 November Reply

    My name is Lia This is exaclty what I have been looking around for contributing very specialized helpful tips. Your site is extremely like a pile of money and is going to facilitate me projects at home. I’m so amazed by the details that everyone on this site. It shows how excellent you has become a mastered concepts. I saved this website page and will returning for trending articles. You my masters are the top talented people. I discovered the know-how that I previoulsy searched internet and simply could not find. What an informative blog. Well, I hope to chat with you soon.

  • Laura Hartis
    Posted at 23:13h, 09 November Reply

    in favor of his web site, because here every information is quality based

  • エアジョーダン 1 ハイ
    Posted at 02:15h, 18 April Reply

    Excellent, what a weblog it is! This webpage gives helpful information to us, keep it up.

  • WilliamCoen
    Posted at 08:57h, 05 May Reply

    Really appreciate you sharing this forum post.Really looking forward to read more. Much obliged. http://hudhfgdfg434tgag.tumblr.com/

  • WilliamCoen
    Posted at 21:43h, 06 May Reply

    Really informative forum.

  • Dick Sanfilippo
    Posted at 14:31h, 19 May Reply

    Astoundingly well crafted and insightful for a freely available
    digital editorial! Thanks a bunch for the share!

Post A Comment